[ndmisiek]

Hello.

At the beginning I wanted to apologize for my "English"
I need help.
I have a problem with the maho mh600w machine on the Philips 532 control machine lost the machine steels stored in the bios.
No service in Poland wants to be repaired, my only hope is that one of you has the same machine and could read this data and help me.

 1_.jpg ( 123.61KB ) Anzahl der Downloads: 67

 2_.jpg ( 43.05KB ) Anzahl der Downloads: 74

 3_.jpg ( 77.42KB ) Anzahl der Downloads: 77

Best wishes
Simon

Der Beitrag wurde von ndmisiek bearbeitet: 21.12.2018, 08:39 Uhr

[mtronik-kit]

Hello.

At the beginning I wanted to apologize for my "English"
I need help.
I have a problem with the maho mh600w machine on the Philips 532 control machine lost the machine steels stored in the bios.
No service in Poland wants to be repaired, my only hope is that one of you has the same machine and could read this data and help me.

 1_.jpg ( 123.61KB ) Anzahl der Downloads: 67

 2_.jpg ( 43.05KB ) Anzahl der Downloads: 74

 3_.jpg ( 77.42KB ) Anzahl der Downloads: 77

Best wishes
Simon

Hello,
have you replaced the battery on the EPC-8 ?

best regards
mtronik

[ndmisiek]

Hello,
have you replaced the battery on the EPC-8 ?

best regards
mtronik

Hello,

Yes I replaced the battery, but I do not have a fixed machine so I ask if anyone could help me.

[mtronik-kit]

Hello,

Yes I replaced the battery, but I do not have a fixed machine so I ask if anyone could help me.

Hello,
here your EXM configuration

Slot 31: FD 01 00
Slot 0: FD 00 00
Slot 1: F7 A1 11

best regards
mtronik

[ndmisiek]

Hello,
here your EXM configuration

Slot 31: FD 01 00
Slot 0: FD 00 00
Slot 1: F7 A1 11

best regards
mtronik

Hello,
Thank you very much for the EXM configuration, the error associated with it has disappeared.
However, the system does not start any more.
Do I have to set up the disk in Bios?
If so, how?

Best Regards
Simon

[mtronik-kit]

Hello,
Thank you very much for the EXM configuration, the error associated with it has disappeared.
However, the system does not start any more.
Do I have to set up the disk in Bios?
If so, how?

Best Regards
Simon

Hello,

I have the other settings here

best regards
mtronik

Angehängte Datei(en)

 VME_2.pdf ( 458.05KB ) Anzahl der Downloads: 59
 VME_1.pdf ( 299.69KB ) Anzahl der Downloads: 54

 

[ndmisiek]

Hello,

Thank you very much for the help the system has started.

However, there was a problem with the fact that the keyboard from the PC must be connected all the time because it does not want to start.

another problem is that the machine does not want to be stressed. The X axis switches off the limit switch. (error x04 max following error too large)

Is it possible that the machine constants have been deleted?

I will add that before the failure everything was ok.

best wishes
Simon

Der Beitrag wurde von ndmisiek bearbeitet: 28.12.2018, 12:43 Uhr

[mtronik-kit]

Hello,

Thank you very much for the help the system has started.

However, there was a problem with the fact that the keyboard from the PC must be connected all the time because it does not want to start.

another problem is that the machine does not want to be stressed. The X axis switches off the limit switch. (error x04 max following error too large)

Is it possible that the machine constants have been deleted?

I will add that before the failure everything was ok.

best wishes
Simon

Hello
The machine parameters have been deleted and must be entered again.
Because of the keyboard I have to check. there is another wrong parameter in the bios

best regards

[ndmisiek]

Hello
The machine parameters have been deleted and must be entered again.
Because of the keyboard I have to check. there is another wrong parameter in the bios

best regards

Hello,


Do you have any parameters? unfortunately, I got documentation for my machine matching Maho 800

best regards
Simon

[mtronik-kit]

Hello,


Do you have any parameters? unfortunately, I got documentation for my machine matching Maho 800

best regards
Simon

I need the exact configuration of the machine.
But it is very difficult to get the right parameters. it is better to ask the pre-owner of the machine.
best regards
mtronik

[ndmisiek]

I need the exact configuration of the machine.
But it is very difficult to get the right parameters. it is better to ask the pre-owner of the machine.
best regards
mtronik

I just talked to the previous owner of the machine unfortunately does not have such data.
What information is exactly needed?

regards
Simon

Der Beitrag wurde von ndmisiek bearbeitet: 28.12.2018, 13:27 Uhr

[mtronik-kit]

I just talked to the previous owner of the machine unfortunately does not have such data.
What information is exactly needed?

regards
Simon

Where's the machine?
You have not entered anything in your profile.

[ndmisiek]

Where's the machine?
You have not entered anything in your profile.

The machine is in Poland near Krakow.
in my opinion, the machine has in the machine constants currently entered a larger range of work in the X axis.

[mtronik-kit]

Where's the machine?
You have not entered anything in your profile.

after switching on the machine you have an error O23 ?

[ndmisiek]

after switching on the machine you have an error O23 ?

after switching on, error I01 appears after starting the machine, there is no error.
the ruler (heidenhain) gives a reading in the range of 450 but it is turned off by the limit switch and does not reach the RF point

Der Beitrag wurde von ndmisiek bearbeitet: 28.12.2018, 14:49 Uhr

[mtronik-kit]

after switching on, error I01 appears after starting the machine, there is no error.
the ruler (heidenhain) gives a reading in the range of 450 but it is turned off by the limit switch and does not reach the RF point

The parameters have to be checked.
you have to ask MAHO for the original parameter.

[ndmisiek]

The parameters have to be checked.
you have to ask MAHO for the original parameter.

hello.

the problem of machine constants has been solved.

there is now a problem after changing the language to English mc memory checksum error appears.

and I can not connect to the machine using the nclink rs 232 program, does anyone have a connection diagram and what data needs to be changed in machine constants?

Regards
Simon

[ndmisiek]

hello.

the problem of machine constants has been solved.

there is now a problem after changing the language to English mc memory checksum error appears.

and I can not connect to the machine using the nclink rs 232 program, does anyone have a connection diagram and what data needs to be changed in machine constants?

Regards
Simon

Hello,

At the beginning I wanted all readers to wish all the best in the new year!

Small update:

I received machine constants from Maho, however I can not connect to the machine via the RS232 port. I use NClink software.
Can anyone help me how to set the machine and how should the configuration of the cable to connect look like?
I use a cable that communicates with the machine on the 432 control but all the time after downloading data from the machine receives a square and you can not send out.

below the cable configuration.

Please help.

Regards
Simon

Der Beitrag wurde von ndmisiek bearbeitet: 03.01.2019, 08:27 Uhr

Angehängte Datei(en)

 20190103_082503.jpg ( 156.27KB ) Anzahl der Downloads: 26

 

[NenadMijajlovic]

Hello everyone,

Could someone please share the machine parameters (machine constants) for a MAHO MH 600W with a Philips 532 control unit?

I need these parameters to restore the machine after settings loss. Any help—screenshots, text files, PDFs, or photos of the “Parameter Screen” values—would be greatly appreciated.

Thank you in advance!