Mark 1 und Mark12 ( Dazwischen aufrufen )

Moin Zusammen
Habe eine DMG CTX 510 Ecoline. ( Siemens Sinumerik 840D )

Habe ein Programm mit Mark 1 bis Mark 12 versehen. ( sollen 12 Ringe werden )

Gibt es eine Möglichkeit z.B. in Mark 5 reinzuspringen?

Wäre super von euch, wenn ich was dazu lernen könnte

Danke euch schon mal im voraus.

Macht's du es mit Shop Turn?

ja.

Vordrehen
Fertigdrehen.
Abstechen

Möchtest du in ein abgebrochenes Programm bei "Ring5" reinspringen?

Stell dein Programm doch mal hier ein.

Gruß Rainer

bitte sehr.
Hoffe man kann das sehen.

ja richtig

Auf deinen Bildern sehe ich nur MARK1 und MARK2

Schreiben wir hier aneinander vorbei?

Du kannst die MPF-Programme aus der Maschine mit dem Texteditor öffnen und hier rein kopieren. Dann wird es lesbar.

Gruß Rainer

Hoffe man kann das verstehen

N2 MARK1: ;#SM;*RO*
N3 F_CON("AK1",4,"E_LAB_A_AK1","E_LAB_E_AK1");*RO*
N4 F_ROU_Z("500 005 CN SCHRUPPER","",1,0.2,3,100,2,0,0,,,,"201803201134500",,,,"201803201134501",321111,0.1,0,0,1,3,0.3,0.075,0,0,0.25,0,1,114.5,90,0.5,90,126,,,,,,,0,0,,,
,,0,,,,0,0,0,1,0,0,0.1);*RO*
N5 F_ROU_Z("510 005 CN SCHLICHTER","",1,0.1,3,100,2,10,0,,,,"2018032011472014","201803201134501",,,"2018032011472015",321211,0,0.1,0.1,2,6,0.5,0.15,0.1,0,0,0,1,0,91,0,91,102,0,,82,,,,2,2,,,,,0
,,,,0,0,0,1,1,0);*RO*
N6 F_CON("IK1",4,"E_LAB_A_IK1","E_LAB_E_IK1");*RO*
N7 F_ROU_Z("500 051 CN SCHRUPPER KURZ","",1,0.2,3,100,2,0,0,,,,"201803201135422",,,,"201803201135423",323121,0.1,0,0,1,3,0.3,0.1,0,0,0.25,0,1,97,90,0,90,118,294,,,,,,0,0,,,,,0,
,,,0,0,0,1,0,0,0.1);*RO*
N8 F_ROU_Z("510 052 CN SCHLICHT KURZ","",1,0.1,3,100,2,10,0,,,,"2018032011474516","201803201135423",,,"2018032011474517",321221,0,0.1,0.1,2,6,0.5,0.15,0.1,0,0,0,1,0,91,0,91,102,0,,82,,,,2,2,,,,,0
,,,,0,0,0,1,1,0);*RO*
N9 F_CON("EK1",4,"E_LAB_A_EK1","E_LAB_E_EK1");*RO*
N10 F_ROU_Z("520 030 EINSTECHER 3.0","",1,0.1,3,600,1,1,0,,,,"201803201140478",,,,"201803201140479",301311,,0.1,0.1,1.5,6,0.1,0.1,0.1,0,0,1,1,0,91,0,91,126,,,,,,,250,350,1,30
,,,0,,,,0,0,0,1,1,0,0.05);*RO*
N11 F_CON("IK2",4,"E_LAB_A_IK2","E_LAB_E_IK2");*RO*
N12 F_ROU_Z("510 999 EINSTICH INNEN","",1,0.05,3,600,1,0,0,,,,"201803261125340",,,,"201803261125341",312221,0.1,0,0,6,3,0,0,0,0,0.25,0,1,99,90,0,90,126,,,,,,,0,0,,,,,0,,,,0,0,
0,1,0,0,0.1);*RO*
N13 F_CON("FK1",2,"E_LAB_A_FK1","E_LAB_E_FK1");*RO*
N14 F_MI_CON("120 030 VHM FRAESER","",1,60,1,3500,1,100002,137,0,90,-4,90,1,0.15,0,0,5,42,0,5,0.05,0,0,1,,,1,2,91);*RO*
N15 F_MI_CON("120 030 VHM FRAESER","",1,60,1,3500,1,100002,138,0,90,-4,90,4,0.5,0,0,5,42,0,5,0.05,0,0,1,,,1,2,91);*RO*
N16 F_PARTOF("520 030 EINSTECHER 3.0","",1,0.03,3,750,1,0,110,-3,97,90,-1,91,0.3,600,0.1,0.2,0,1000,0,0,0,1);*RO*
N17 F_HOME
N18 M00
N19 M67 ;TUER ENTRIEGELN
N20 MARK2: ;#SM;*RO*
N21 ATRANS Z-6.1 ;#SM;*RO*
N22 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N23 ATRANS Z-6.1 ;#SM;*RO*
N24 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N25 ATRANS Z-6.1 ;#SM;*RO*
N26 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N27 ATRANS Z-6.1 ;#SM;*RO*
N28 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N29 ATRANS Z-6.1 ;#SM;*RO*
N30 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N31 ATRANS Z-6.1 ;#SM;*RO*
N32 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N33 ATRANS Z-6.1 ;#SM;*RO*
N34 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N35 ATRANS Z-6.1 ;#SM;*RO*
N36 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
N37 ATRANS Z-6.1 ;#SM;*RO*
N38 REPEAT MARK1 MARK2 P=1 ;#SM;*RO*
F_END(0,1,0);*RO*
M30 ;#SM;*RO*
E_LAB_A_AK1: ;#SM Z:6
;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G18 G90 DIAM90;*GP*
G0 Z0 X96 ;*GP*
G1 X107 ;*GP*
Z-.529 X113 RND=.1 ;*GP*
Z-6.3 ;*GP*
X115 ;*GP*
;CON,V64,2,0.0000,4,4,MST:3,2,AX:Z,X,K,I,TRANS:0;*GP*;*RO*;*HD*
;S,EX:0,EY:96,ASE:90;*GP*;*RO*;*HD*
;R,RROUND:0;*GP*;*RO*;*HD*
;LU,EY:107;*GP*;*RO*;*HD*
;LA,EY:113,ASE:100;*GP*;*RO*;*HD*
;R,RROUND:.1;*GP*;*RO*;*HD*
;LL,EX:-6.3;*GP*;*RO*;*HD*
;LU,DEY:1;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_AK1:
E_LAB_A_IK1: ;#SM Z:7
;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G18 G90 DIAM90;*GP*
G0 Z0 X101.15 ;*GP*
G1 X100.15 RND=.5 ;*GP*
Z-5.5 ;*GP*
X97 ;*GP*
;CON,V64,2,0.0000,0,0,MST:3,2,AX:Z,X,K,I,TRANS:0;*GP*;*RO*;*HD*
;S,EX:0,EY:100.15,ASE:270;*GP*;*RO*;*HD*
;R,RROUND:.5;*GP*;*RO*;*HD*
;LL,EX:-5.5;*GP*;*RO*;*HD*
;LD,EY:97;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_IK1:
E_LAB_A_EK1: ;#SM Z:10
;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G18 G90 DIAM90;*GP*
G0 Z-1.3 X113 ;*GP*
G1 Z-1.5 RND=.2 ;*GP*
X110 ;*GP*
Z-6 ;*GP*
X113 ;*GP*
;CON,V64,2,0.0000,2,2,MST:3,2,AX:Z,X,K,I,TRANS:0;*GP*;*RO*;*HD*
;S,EX:-1.5,EY:113,ASE:180;*GP*;*RO*;*HD*
;R,RROUND:.2;*GP*;*RO*;*HD*
;LD,EY:110;*GP*;*RO*;*HD*
;LL,EX:-6;*GP*;*RO*;*HD*
;LU,EY:113;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_EK1:
E_LAB_A_FK1: ;#SM Z:5
;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G17 G90 DIAMOF;*GP*
G0 X50.05 Y1.75 ;*GP*
G1 X53.95 RND=1.75 ;*GP*
Y-1.75 RND=1.75 ;*GP*
X50.05 ;*GP*
;CON,0,0.0000,1,1,MST:0,0,AX:X,Y,I,J,TRANS:1;*GP*;*RO*;*HD*
;S,EX:50.05,EY:1.75;*GP*;*RO*;*HD*
;F,LFASE:0;*GP*;*RO*;*HD*
;LR,EX:53.95;*GP*;*RO*;*HD*
;R,RROUND:1.75;*GP*;*RO*;*HD*
;LD,EY:-1.75;*GP*;*RO*;*HD*
;R,RROUND:1.75;*GP*;*RO*;*HD*
;LL,EX:50.05;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_FK1:
E_LAB_A_IK2: ;#SM Z:5
;#7__DlgK contour definition begin - Don't change!;*GP*;*RO*;*HD*
G18 G90 DIAM90;*GP*
G0 Z-2 X98.368 ;*GP*
G1 Z-3 X101.832 ;*GP*
Z-4 X98.368 ;*GP*
;CON,V64,2,0.0000,2,2,MST:3,2,AX:Z,X,K,I,TRANS:0;*GP*;*RO*;*HD*
;S,EX:-2,EY:98.368,ASE:90;*GP*;*RO*;*HD*
;R,RROUND:0;*GP*;*RO*;*HD*
;LA,EX:-3,EY:101.832;*GP*;*RO*;*HD*
;LA,EX:-4,EY:98.368;*GP*;*RO*;*HD*
;#End contour definition end - Don't change!;*GP*;*RO*;*HD*
E_LAB_E_IK2:

Das geht meines Wissens nach nicht. Man muss die Ringe trennen und für jedes Rind eigenes Nullpunkt machen. Dann kannst du einsteigen.

Oder du tust den Nullpunkt an den abgebrochenen Teil anpassen. Und änderst im Programm die Stückzahl was noch runter kommen sollte .

frigat76 war schneller

Ich seh das genauso.

Schade.

Davon wollte ich ja weg kommen.

Also das mit NPV neu setzen oder Einzelprogramm. ( habe 3 verschiedene Programme )

Trotzdem danke euch für eure Mühe.